If you're keen on utilising solar energy then this hot water cylinder is for you. The coil design is created for use with closed loop solar systems. This is where the heat transfer fluid is circulated through the solar collector on the roof where it is heated by the sun. The heated transfer fluid then passes through the cylinder coil, which acts like a very large element to heat the water.
The unique coil spirals down and then wraps back up around itself creating a coil within a coil. It is located at the very bottom of the cylinder to allow for maximum heat to be transferred to the water in the cylinder.
The duplex stainless steel inner cylinder means it can be used is solar systems with high incoming water temperatures.
Suitable for:
- indoor installations only
- mains and low pressure systems
- connection to closed loop solar systems
- residential and light commercial water heating applications
No suitable as a pool or spa heater, or for underfloor heating.
Water quality
Rinnai cylinders are manufactured to suit most NZ council water supplies. However some supplies can have a detrimental effect on the cylinder, its operation and life expectancy. Stainless steel cylinders are not suitable for bore or tank water.
Single coil lower element
For new builds and renovations connecting to a closed loop solar system, where the homeowner wants constant hot water, whether there is solar gain or not.
Single coil dual element
For new builds and renovations connecting to a closed loop solar system, where the homeowner wants faster recovery times, and to reduce the risk of running out of hot water regardless of solar gain. Cylinder will have higher running costs.
Single coil upper element
For new builds and renovations connecting to a closed loop solar system, where the homeowner relies heavily on solar gain. Upper element is only used to quickly heat water in the top of the cylinder.
10 years
IPX1
supplied
• 190 L 2 kW - MS190550C20
• 190 L 3 kW - MS190550C30
• 250 L 2 kW - MS250560C20
• 250 L 3 kW - MS250560C30
• 300 L 2 kW - MS300560C20
• 300 L 3 kW - MS300560C30
• 250 L 2 kW - MS250560CU20
• 250 L 3 kW - MS250560CU30
• 300 L 2 kW - MS300560CU20
• 300 L 3 kW - MS300560CU30
• 250 L 2 kW - MS250560CD20
• 250 L 3 kW - MS250560CD30
• 300 L 2 kW - MS300560CD20
• 300 L 3 kW - MS300560CD30
Inner, high grade duplex stainless steel
Outer, galvanised steel
CFC free polyurethane foam, compliant with NZ MEPS
Hot and cold connections ¾ " (20 mm)
TPR ½ " (15 mm)
• Solar coil ¾ " 20 mm diameter
• Length = 14 m (1.1 m2)
• Maximum kW output 21.4 kW
Incoloy 825 alloy sheath element, options; 2 kW, 3 kW, 2 x 2 kW, and 2 x 3 kW
Robert Shaw 30 A contact auto-reset (red dial)
TPR supplied, 850 kPa, 99 °C, 10 kW
This cylinder MUST be installed with a 500 kPa or less pressure limiting valve and appropriate cold water expansion valve.
| Model | Empty | Full |
| 190 L | 42 kg | 232 kg |
| 250 L | 48 kg | 298 kg |
| 300 L | 56 kg | 356 kg |
No cylinder wrap required. All Rinnai cylinders meet the NZ Minimum Energy Performance Standard (MEPS).
June 2022
• Thermostat Robert Shaw red dial (ART solar) - 30015
• Kawai element solar 2 kW 230 V - 30062
• Kawai element solar 3 kW 230 V - 30063
• TPR MP 850 kPa 15 mm - 30018
This article clarifies some of your frequently asked questions amidst all the confusion about the future of gas.
Read Article
Hot water can make up a third of our electricity bill! This ends up being a lot of amount of money as time goes by. With a few small changes in our daily habits and routines, we can cut down on these costs.
Read Article
New Zealand's abundant supply of low-cost firewood makes it a great option to heat a home's water via a wetback accessory and a specialised hot water cylinder.
Read Article
