Includes engine ($4051), frame ($541), and burn media ($291)
Enjoy a warm welcome home with the Rinnai Ember, the little hottie that offers a stunning glow of a wood fire, the superior warmth of a gas fire, and none of the hard work!
A small gas fire with compact dimensions suitable for new builds and renovations. The Rinnai Ember is available in two sizes and delivers over 5 kW of heat output.
With stunning burn media options, large viewable flame area, and frame choices to suit your lifestyle.
Temperature control
Back-to-basics simple infra-red remote makes operation easy and stress free, or upgrade to Wi-Fi capability with our Wi-Fi module retrofit kit, part number R7000 (RRP $220 plus installation). This will need to be fitted by a licensed gasfitter.
Suitable for masonry installations and installations into a mock (false) chimney in open plan areas and living rooms. For masonry installations the chimney cavity needs to be at least 200 x 200 mm in order to fit the colinear flexi flue.
Heating areas (up to)
- Upper North Island: 80 m2 (600), 96 m2 (700)
- Central and lower North Island: 55 m2 (600), 66 m2 (700)
- South Island: 46m2 (600), 56 m2 (700)
Room size consideration
Smaller rooms will heat up quickly, and due to the efficiency of the appliance, the fire will turn to a low setting once the set temperature has been reached.
12-27
MJ/h
2.5-6.0
kW
77%
Available for Natural Gas or LPG, specify at the time of purchase
120 V AC 50 Hz 2-speed centrifugal blower. Heat is distributed from the top of the appliance.
Located on the lower RHS of the base panel, in front of the gas control.
Brass ½ " BSPT male fitting. The gas supply terminates inside the heater, lower RHS of the appliance.
230-240 V AC 50 HZ high voltage electronic spark generation unit.
37-45 dB(A)
Colinear flexi flue, air intake Ø 75 mm, exhaust Ø 100 mm. Appliance must be installed with a Rinnai Ember flue system.
Colinear (air intake Ø75 mm, exhaust Ø100 mm) to coaxial direct vent flueing (inner Ø100 mm, outer Ø170 mm). Appliance must be installed with a Rinnai Ember flue system.
The Ember has a 1.5 m power cord with a 3-pin plug supplied. The power cord passes through a slot in the back right hand corner of the appliance.
Flame failure sensing system, pressure relief, overheat safety switch, air temperature sensor, thermal fuse, overcurrent fuse, and spark detector.
Operated using a basic infra-red remote, or for more features such as timers and thermostatic control, by using a Wi-Fi module (purchased separately) and using the Rinnai Wi-Fi fireplace controller app.
The minimum clearances listed below are measured from the edge of the outer glass.
These are the unit dimensions only, not the framing/cavity dimensions
Viewable glass dimensions
- Ember 600: 535 (w) x 500 (h) mm
- Ember 700: 638 (w) x 500 (h) mm
Energy Safety Supplier Declaration of Compliance: Declaration number - 1810620176
June 2017
What makes a great fireplace? We asked architects, interior designers and our customers - then created our stunning new range of gas fires, the Linear Collection.
Read ArticleThere are many things to consider when choosing a gas fire. So we’ve considered them for you and put them all into this article.
Read ArticleA cold home is an unhealthy home. And there are more unhealthy homes in New Zealand than you probably realise.
Read ArticleOur stylish and efficient heating and cooling solutions are designed to bring you total home comfort.
FIND OUT MORESimply enter the product code and serial number to register a Rinnai product.
REGISTER A PRODUCT