Get a warm welcome home with the new Rinnai Ember Series. RRP $4,883
*Includes engine ($4051), frame ($541), and burn media ($291)
Enjoy a warm welcome home with the new Rinnai Ember, the little hottie that offers the stunning glow of a wood fire, the superior warmth of a gas fire - and none of the hard work!
A small gas fire with compact dimensions suitable for both new builds and renovations, the Rinnai Ember is available in two sizes and delivers over 5 kW of heat output.
With stunning burn media options, large viewable flame area and frame choices to suit your style.
Suitable for Masonry installations and installations into a mock (false) chimney in open plan areas and living rooms.
Heating areas (up to) - Upper North Island: 85 m² (Ember 600), 99 m² (Ember 700) - Central and lower North Island: 74 m² (Ember 600), 87 m² (Ember 700) - South Island: 55 m² (Ember 600), 65 m² (Ember 700)
Gas type Available for Natural Gas or LPG, specify gas type at time of purchase.
Installation considerations Masonry installations—chimney cavity needs to be at least 200 x 200 mm in order to fit the colinear flexi flue.
Room size—smaller rooms will heat up quickly, and due to the efficiency of the appliance, the heater will turn to a low flame setting once the set temperature has been reached.
For efficient performance Rinnai recommends installing the fire as close to the floor as possible. If the unit is installed higher up the wall the movement of air from the convection fan, depending on the room configuration, could create draughts.
General clearances around the Ember when operating The clearances shown below, measured from the edge of the outer glass, are minium clearances unless otherwise stated. The appliance must not be installed where curtains or other combustibles (coffee tables, couches etc.) could come onto contact with it. In some cases curtains may need restraining.
The 400 mm side clearance includes side walls. The 1000 mm clearance is in front of the fire.
Located on the lower RHS of base panel, in front of the gas control.
Convection fan
120 V AC 50 HZ 2-speed centrifugal blower. Heat is distributed from the top of the appliance.
Gas connection
Brass ½ " BSPT male fitting, the gas supply terminates inside the heater—lower RHS of the appliance.
Ignition
230-240 V AC 50 Hz high voltage electronic spark generation unit.
Noise level
37-45 dB(A)
Flueing - masonry
Colinear flexi flue, air intake Ø 75 mm, exhaust Ø 100 mm. Appliance must be installed with a Rinnai Ember flue system.
Flueing - mock chimney
Colinear (air intake Ø 75 mm, exhaust Ø 100 mm) to coaxial direct vent flueing (inner Ø 100 mm, outer Ø 170 mm). Appliance must be installed with a Rinnai Ember flue system.
Power consumption and electrical supply
High 110 W, standby < 1 W. This heater has a 1.5 m power cord with a 3-pin plug supplied. The power cord passes through a slot in the back right hand corner of the appliance.
Safety devices
Flame failure sensing system, pressure relief, overheat safety switch, air temperature sensor, thermal fuse, overcurrent fuse, and spark detector.
Temperature control
Once the unit is turned on the infra-red remote (temp. sensor located in the bottom of the remote) is used to control the flame height and heat output. If the remote is not used the Ember will modulate between the burner settings to maintain the default set temperature of 22 °C.
Weight
Ember 600: 51 kg
Ember 700: 55 kg
Compliance
Supplier declaration of compliance: Declaration number - 1810620176
Market release
June 2017
* kW output and energy star rating will vary according to model, gas type, and flue configuration.