RRP $3,240
*RRP includes the iHeat unit and thermostat. Pricing does not include installation or additional components such as ducting, vents etc. An indicative total installed cost is $7K-$12K. To evaluate the actual installed cost contact an iHeat installer who can assess all the requirements for your home.
**The Rinnai iHeat will be available until the end of December 2018 or until stocks run out**
The Rinnai iHeat is a ducted home heating system that uses hot water from your Rinnai INFINITY* continuous flow water heater to warm air and circulate it around your home. The Gas central heating system can also be zoned to only heat the areas you are using. Zoning kits are available from ducting suppliers, refer p. 2 of the 'Ducting Guidelines' PDF at the bottom of the 'Technical' tab.
Whole home heating that is fast and efficient
With the same high efficiency as your Rinnai INFINITY continuous flow water heater and heat output of 20 kW, the Rinnai iHeat will be efficient and fast at heating your home.
How it works
The Rinnai INFINITY* provides hot water to the iHeat air handler unit (heat exchanger). The heat exchanger extracts the heat from the hot water and transfers it to a steady stream of air. This air is fed into the ducting system and is distributed into each room.
Suitable for
Homes with a gas connection and an existing Rinnai INFINITY* (or planned installation of a continuous flow hot water unit).
Homes where the iHeat unit can be installed in a ceiling space, or under the floor—subject to the clearances shown below. The unit cannot be positioned outside.
• Heating area: Up to 250 m² (depending on where you live)
• Number of outlets: 3-12 (each outlet provides approx.1.8 kW)
Hard or acidic water will need to be treated to use this product.
Clearances
The iHeat should be positioned so that the LED's are easily visible through the window of the control board. Avoid positions that make access to the iHeat and removing components difficult.
• Above unit: 450 mm minimum
• Sides of unit: 750 mm minimum
• Front and behind unit: 1 m minimum
|
Gas Type: NG, LPG Heating output: 6 - 20kW Max star rating: 7.0 Installation: Ceiling, subfloor Flued: No Remote: Yes Ducted Heating: 3 to 12 ducts Energy Star mark: No Warranty: 3 years parts and labour |
Gas Type: NG, LPG Heating output: 2.4 – 8.1kW Max star rating: 5.7 Fascia option: Blk on Blk, SS on Blk Burn Media options: Glowing river stones, Silky oak logset Remote: Yes Ducted Heating: No Energy Star mark: Yes Warranty: 2 years |
Gas Type: NG, LPG Heating output: 3.8 - 7.5kW Max star rating: 4.2 Fascia option: Flat Blk on Blk, Flat SS on Blk, Blk Granite, Blk on Blk, SS on SS Burn media options: Driftwood logset Remote: Yes Ducted Heating: Yes Energy Star mark: Yes Warranty: 2 years |
Gas Type: NG, LPG Heating output: 1.9-5.3kW Max star rating: 4.8 Installation: Floor Mounted Flued: Yes Remote: No Ducted Heating: No Energy Star mark: Yes Warranty: 2 years |
| Energy Efficiency | Approx. the same as the Rinnai Infinity—over 80% depending on the Infinity model and ducting used. |
| Heating Area | Up to 250 m² (depending on where you live and how well insulated your house is). |
| Minimum Pipe Size | 20 mm external diameter pipe |
| Noise Level: Fan | Fan: 40-50 dB(A). From various charts on the Internet 40 dB(A) is the same as standing 1.5 m away from a refrigerator. Please note: If the system is balanced properly the fan noise will be neglible. |
| Noise Level: Rinnai Infinity | 50 dB(A) approx. |
| Number of Outlets | 3-12, each outlet provides approx. 1.8 kW |
| Nominal Electrical Consumption | Does not include the Rinnai Infinity. • Heating Fan Hi: 710 W • Heating Fan Lo: 300 W • Air Circulation Fan Hi: 580 W • Air Circulation Fan Lo: 165 W |
| Power Output | Nominal 20 kW, maximum 25 kW (depending on installation). Power output of fan is 0.6 kW. |
| Return Air Intake | Min. size is 1500 cm². Return air filter is mandatory. |
| Spigot Size | • Supply air: 300 mm ID • Return air: 350 mm ID Approx. external diameter of return air ducting—430 mm. |
| Weight | Total shipping weight approx. 56.4 kg |
| Market Release | February 2013 |
Additional dimensions
• Approximate end-to-end measurement = 1135 mm
• Total height of unit with a suspended mounting kit is 910 mm
• Total width of unit is 790 mm—this includes the control box.
We’re happy to help with anything, big or small. Please fill out the short form below and we’ll get back to you within 24 hours.
